- Can you over tighten a chainsaw chain?
- Why does my chainsaw chain keep getting tight?
- What makes a chainsaw not cut straight?
- Can a chainsaw get too hot?
- Why does my chainsaw smoke when cutting?
- Why does my chainsaw chain dull so quickly?
- What happens when a chainsaw overheats?
- Should you smoke a chainsaw?
- How tight should you tighten a chainsaw chain?
- Is it OK to cut wet wood with a chainsaw?
- How do I know if my chainsaw bar is bad?
- Is it worth sharpening a chainsaw chain?
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw.
To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise.
Don’t over-tighten the chain as this could cause it to break..
Why does my chainsaw chain keep getting tight?
Re: Chain tightens by itself Sounds like the bar’s sprocket nose may be wore out or broken . A roller bearing may have popped out and is spreading the nose or jammingthe chain up. Check to see if the sprocket nose on the bar is same pitch as rim sprocket and chain.
What makes a chainsaw not cut straight?
Most of the time when a saw won’t cut straight, it’s caused by a problem with the saw chain. … It seem logical a bent bar would cause this, because it is is what guides the chain. If they find a little bend in the bar, they figure they’ve found the problem. Some will straighten the bar, others will replace it.
Can a chainsaw get too hot?
Yes, chainsaws can overheat but it shouldn’t happen under normal conditions. If the engine is running too hard or if it doesn’t get sufficient ventilation or lubrication it can quickly overheat, which can lead to malfunction.
Why does my chainsaw smoke when cutting?
While a chain saw does produce some heat while in use, it should never overheat or begin smoking. … The most likely causes of smoking and overheating are a lack of air and/or a lack of lubrication to the engine or the chain saw chain guide bar.
Why does my chainsaw chain dull so quickly?
If your chain dulls quickly, then it could be a couple of things. Check your user’s manual to ensure that you are using the right sized file for your chain. Alternatively, you could be applying too much pressure when you file. This will create cutting edges that are too thin and dull quickly.
What happens when a chainsaw overheats?
If you use it too much while it’s overheating, it’s possible you may burn out the engine or pistons causing you to have a broken chainsaw that will either need to be repaired or replaced. Following these tips can help to keep your chainsaw running smoothly for years to come.
Should you smoke a chainsaw?
It isn’t normal for a chainsaw to smoke, but if it does happen it can be the result of the chainsaw overheating, the fuel mix containing too much oil, or the chain either not being sharp enough or not getting enough lubrication. In short, a smoking chainsaw is a sure sign that something isn’t right.
How tight should you tighten a chainsaw chain?
Before explaining the tensioning steps, we should explain what proper chainsaw chain tension looks like. A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Is it OK to cut wet wood with a chainsaw?
In all honesty, no! The additional moisture found on wet wood will not make any difference to the cutting process. It doesn’t place any additional resistance on the chainsaw, and no additional effort is required to cut through it.
How do I know if my chainsaw bar is bad?
A bar heel with a lot of wear may have shallow rails. In extreme cases, the groove will get so shallow, you may see where the chain’s drive links have rubbed in the bottom of the groove. If you find this at any location on the bar, your inspection is over. The bar is worn out and needs to be replaced.
Is it worth sharpening a chainsaw chain?
The correct file to sharpen any given chain is worth less than five bucks. It will touch up a chain and keep it sharper than new literally a hundred times (assuming there is no physical damage to the chain). You can sharpen a chain until the little slash mark at the back of the tooth. It is, however, a learned skill.